You’re tired of watching your energy bills spike every time the temperature drops. A heat pump installation in Hollywood Park, TX changes that equation entirely.
Here’s what actually happens after installation. Your system pulls heat from outside air even when it feels cold, using electricity to move heat rather than generate it. That’s why heat pumps are 2-3 times more efficient than gas furnaces in Texas climate conditions.
Most Hollywood Park homeowners see their heating costs drop by 30-40% in the first year. You’re also getting better humidity control during those long Texas summers, which means your home feels comfortable at higher thermostat settings. That’s more savings on top of the heating efficiency gains.
The federal government is backing this technology with up to $2,000 in tax credits covering 30% of your installation cost. You’re not just saving monthly, you’re getting money back at tax time while increasing your home’s resale value by $4,000-$8,000 according to recent appraisal data.
We’re veteran-owned and have been installing HVAC systems across San Antonio, Austin, and Houston for over 20 years. We’re not a franchise operation or a national chain trying to hit quotas.
Hollywood Park homes built in the 1970s require careful attention to ductwork sizing and electrical capacity before heat pump installation. Our technicians assess these factors during the estimate, not after you’ve already signed a contract. That’s how we avoid the surprise costs and change orders that give this industry a bad reputation.
You’re working with licensed, certified technicians who show up on time and explain what’s happening in plain language. We offer 24/7 emergency service because Texas weather doesn’t respect business hours, and neither do HVAC failures.
Your installation starts with a home assessment. We measure your square footage, check your existing ductwork, and evaluate your electrical panel capacity. Heat pumps need proper sizing or you’ll end up with short-cycling and efficiency loss.
You’ll get a written estimate that breaks down equipment costs, labor, and any necessary upgrades to ductwork or electrical systems. No vague line items. No “we’ll figure it out later” pricing.
Installation day typically takes 6-10 hours depending on your home’s configuration. We remove your old system, install the new heat pump and air handler, connect refrigerant lines, wire the thermostat, and test the entire system under load. You’ll see us check airflow at every register and verify the system is hitting target temperatures before we leave.
After installation, we walk you through the new thermostat settings and maintenance schedule. You’re getting a system that should run 15-20 years with basic filter changes and annual tune-ups. We provide written warranties on both equipment and labor so you know exactly what’s covered.
Ready to get started?
Your installation covers the complete system: outdoor heat pump unit, indoor air handler, refrigerant lines, thermostat, and all electrical connections. We’re also checking your ductwork for leaks and proper sizing because even the best heat pump won’t perform if air isn’t moving correctly through your home.
Hollywood Park’s median home age means many properties need duct modifications or sealing before installation. We handle that work as part of the project when needed. You’re also getting a full electrical assessment to confirm your panel can handle the heat pump’s power requirements without overloading circuits.
Texas climate makes heat pumps particularly effective here. You’re getting a system designed for long, hot summers and mild winters, which is exactly what Hollywood Park delivers. The same unit that keeps you cool in July will heat your home efficiently when February brings those unexpected cold snaps.
We include a complete walkthrough of your new system’s operation, maintenance requirements, and warranty details. You’ll know how to change filters, when to schedule service, and what sounds are normal versus signs of trouble. Most importantly, you’ll have our 24/7 emergency number for those times when something goes wrong outside business hours.
Installation typically runs $5,000-$12,000 depending on your home’s size, the system capacity you need, and whether your existing ductwork and electrical panel require upgrades. That’s the honest range, not a lowball estimate designed to get us in the door.
Here’s what drives the cost up or down. A 1,500 square foot home with good existing ductwork and adequate electrical capacity will land on the lower end. A 3,000 square foot home that needs duct modifications and a panel upgrade will cost more. We’re not hiding that reality.
The federal tax credit covers 30% of your installation cost up to $2,000, which brings your net investment down considerably. Most Hollywood Park homeowners recoup their investment within 5-10 years through energy savings alone, and you’re adding $4,000-$8,000 to your home’s value immediately. You’re not spending money, you’re moving it from monthly utility bills into home equity.
Modern heat pumps work effectively down to about 25-30°F, and newer cold-climate models perform well even below that threshold. Hollywood Park’s average winter low is 40°F, which means heat pumps operate at peak efficiency throughout most of our heating season.
During extreme cold events like the 2021 winter storm, heat pump efficiency does decrease. That’s physics, not equipment failure. Most systems include auxiliary electric heating strips that automatically kick in when outdoor temperatures drop below the heat pump’s effective range. You’ll still have heat, it just costs more to run during those few days of extreme cold.
Here’s the practical reality: Hollywood Park experiences maybe 5-10 days per year when temperatures drop low enough to reduce heat pump efficiency. The other 355 days, you’re saving 30-40% on heating and cooling costs compared to traditional systems. That math works strongly in your favor even accounting for occasional cold snaps.
Most installations take 6-10 hours from start to finish. You’re looking at a single-day project unless we discover issues with your ductwork or electrical system that require additional work.
The timeline breaks down like this: 1-2 hours removing your old system and preparing the installation site, 3-4 hours installing the new outdoor unit and indoor air handler, 1-2 hours running and connecting refrigerant lines, and 1-2 hours for electrical connections, thermostat setup, and system testing. We’re not rushing through critical steps to hit some arbitrary completion time.
If your home needs duct modifications or electrical panel upgrades, that adds time. We’ll identify those requirements during the initial assessment so you know the full timeline before we start. You won’t come home to find us still working because “we found something” that should have been obvious from the beginning.
Sizing depends on your home’s square footage, insulation quality, window efficiency, ceiling height, and sun exposure. There’s no simple “X tons per square foot” formula despite what some contractors claim.
A proper load calculation takes 30-45 minutes and accounts for all these factors. Undersized systems run constantly and never quite reach target temperatures. Oversized systems short-cycle, turning on and off repeatedly, which wastes energy and wears out components faster. Both scenarios cost you money and comfort.
Hollywood Park homes average 2,200 square feet and typically need 2.5-4 ton systems depending on the variables mentioned above. We perform Manual J load calculations on every installation to get sizing right the first time. You’re not getting a guess based on your neighbor’s system or some outdated rule of thumb.
Heat pumps actually require less maintenance than combustion heating systems because there’s no flame, no gas lines, and no carbon monoxide risk. You’re looking at basic filter changes every 1-3 months and annual professional tune-ups.
Your annual service includes refrigerant level checks, electrical connection inspection, airflow measurement, and cleaning of both indoor and outdoor coils. That’s about the same maintenance schedule as a standard air conditioner, which makes sense because a heat pump is essentially an air conditioner that can reverse its operation to provide heating.
The outdoor unit needs clear space around it for proper airflow. Keep plants, leaves, and debris away from the unit, and occasionally spray down the outdoor coils with a garden hose to remove dust and pollen. That’s the extent of homeowner maintenance beyond filter changes. You’re not dealing with pilot lights, burner adjustments, or combustion chamber cleaning like you would with a furnace.
Older ductwork can work with heat pumps, but it often needs modifications. Heat pumps move air differently than furnaces, and ductwork sized for a furnace may need adjustments to handle heat pump airflow requirements.
We inspect your existing ducts during the assessment and test for leaks using pressure measurements. Many Hollywood Park homes built in the 1970s have duct leakage rates of 20-30%, which means you’re heating and cooling your attic instead of your living space. Sealing those leaks improves efficiency regardless of what heating system you’re running.
Sometimes duct resizing is necessary, particularly if you’re upgrading from an older, smaller system to a properly-sized modern heat pump. We’ll identify any required duct work during the estimate phase with specific explanations of why modifications are needed. You’re getting the information upfront, not after we’ve already started tearing into your system.
Local Resources
Other Services we provide in Hollywood Park
Call Now
